Power Electronics MCQ serires 1

Power Electronics MCQ series
🔥#1 Top 20 MCQ Of  Power Electronics | LMRC | UPPCL-JE | All Competitive Exam MCQ | Important MCQ |
Power electronics MCQ Series – 1

Top 20 questions of power electronics. For explanation of each answer you can watch my video

Question 1: A thyristor is basically

  • PNPN device
  • A combination of diac and triac
  • A set of SCRs
  • A set of SCR, diac and a triac

Answer: PNPN device

Question 2: A silicon controlled rectifier (SCR) is a

  • Unijunction device
  • Device with three junction
  • Device with four junction
  • None of the above

Answer: Device with three junction

Question 3: A thyristor equivalent of a thyratron tube is a

  • Diac
  • Triac
  • Silicon controlled rectifier
  • None of the above

Answer: Silicon controlled rectifier

Question 4: An SCR is made up of silicon because

  • Silicon has large leakage current than germanium
  • Silicon has small leakage current than germanium
  • Silicon has small leakage voltage than germanium
  • Silicon has large leakage voltage than germanium

Answer: Silicon has small leakage current than germanium

Question 5: An SCR is considered to be a semi controlled device because

  • It can be turned OFF but not ON with a gate pulse.
  • It conducts only during one half cycle of an alternating current wave.
  • It can be turned ON but not OFF with a gate pulse.
  • It can be turned ON only during one half cycle of an AC.

Answer: It can be turned ON but not OFF with a gate pulse.

Question 6: Which statement is true for latching current ?

  • It is related to turn off process of the device.
  • It is related to conduction process of device.
  • It is related to turn on process of the device.
  • Both C and D.

Answer: It is related to turn on process of the device.

Question 7: If holding current of a thyristor is 2 mA then latching current should be

  • 0.01 A.
  • 0.002 A.
  • 0.009 A.
  • 0.004 A

Answer: 0.004 A

Question 8: In reverse blocking mode of a thyristor

  • junction J2 is in reverse bias and J1, J3 is in forward bias.
  • junction J3 is in forward bias and J1, J2 in reverse bias.
  • junction J1, J3 is in reverse bias and J2 is in forward bias.
  • junction J1 and J2 is in forward bias and J3 is in reverse bias.

Answer: junction J1, J3 is in reverse bias and J2 is in forward bias.

Question 9: During the commutation period in 3 phase converter, overlap time is

  • Dependent on the load current
  • Dependent on the voltage
  • Dependent on both the load current and load voltage behind the short circuit current
  • Independent on both the load current and load voltage

Answer: Dependent on both the load current and load voltage behind the short circuit current

Question 10: A UJT has ___________.

  • Two pn junctions
  • One pn junction
  • Three pn junctions
  • None of the above

Answer: One pn junction

Question 11: The UJT may be used as ___________.

  • Am amplifier
  • A sawtooth generator
  • A rectifier
  • None of the above

Answer: A sawtooth generator

Question 12: The fig. below represents a

  • Triac thyristor
  • Diac trigger
  • Diode rectifier
  • None of the above

Answer: Diac trigger

Question 13: A diac has ______________ pn junctions.

  • One
  • Two
  • Three
  • Four

Answer: Two

Question 14: What is a TRIAC?

  • Two thyristors connected in series mode
  • Two thyristors connected in parallel mode
  • Two thyristors connected in anti parallel mode
  • Two transistors connected in anti parallel mode

Answer: Two transistors connected in anti parallel mode

Question 15: For an SCR, dv/dt protection is achieved through

  • RC across SCR
  • RL in series with SCR
  • L across SCR
  • L in series with SCR

Answer: RC across SCR

Question 16: Power diode is __________

  • a three terminal semiconductor device
  • a two terminal semiconductor device
  • a four terminal semiconductor device
  • a three terminal analog device

Answer: a two terminal semiconductor device

Question 17: An ideal power diode must have

  • low forward current carrying capacity
  • large reverse breakdown voltage
  • high ohmic junction resistance
  • high reverse recovery time

Answer:

Question 18: A diode is said to be forward biased when the

  • cathode is positive with respect to the anode
  • anode is positive with respect to the cathode
  • anode is negative with respect to the anode
  • both cathode & anode are positive

Answer: anode is positive with respect to the cathode

Question 19: To make a signal diode suitable for high current & high voltage carrying applications with minimum losses, ________

  • a lightly doped n layer is grown between the two p & n layers
  • a heavily doped n layer is grown between the two p & n layers
  • a lightly doped p layer is grown between the two p & n layers
  • a heavily doped p layer is grown between the two p & n layers

Answer: a lightly doped n layer is grown between the two p & n layers

Question 20: Which one of the following statements is TRUE for an ideal power diode?

  • Reverse recovery time is non zero and reverse saturation current is zero
  • Forward voltage drop is zero and reverse saturation current is non zero
  • Forward voltage drop is non zero and reverse recovery time is zero
  • Forward voltage drop is zero and reverse recovery time is zero

Answer: Forward voltage drop is non zero and reverse recovery time is zero


FAQ

What is a thyristor ?

Thyristor is also called a silicon-controlled rectifier (SCR), it is basically a four-layer three-junction pnpn device. It has three terminals: anode, cathode, and gate.
Thyristor is basically an electronic switching device which can remain in conducting (on) and nonconducting state. However, it is a unidirectional device and can conduct only in one direction like a diode. The switching state of the device can be controlled by one of its terminals.

What is silicon controlled rectifier (SCR)?

The thyristor is also called a silicon-controlled rectifier (SCR), it is basically a four-layer three-junction pnpn device. It has three terminals: anode, cathode, and gate.
The silicon control rectifier (SCR) consists of four layers of semiconductors, which form NPNP or PNPN structures, having three P-N junctions labeled J1, J2 and J3, and three terminals.

Which thyristor is equivalent of a thyratron tube?

SCR, The thyratron is a type of gas-filled tube which is used as a high voltage electrical switch and a controlled rectifier.

Why SCR is considered to be a semi controlled device ?

During positive half cycle SCR is in forward blocking mode. By applying gate pulse the SCR can be turned ON during forward blocking mode. But SCR can not be turned OFF by applying gate pulse. It automatically turns off when anode current is below the Holding current. That is why it is called semi controlled rectifier.

What is latching current?

Latching current is the minimum required anode current to turn on SCR. Latching current is 2 or 3 times of holding current

What is holding current?

Holding current is the minimum anode current below which SCR get turn off. Holding current is 2 or 3 times less than latching current.

What is reverse blocking mode of a thyristor?

When a negative voltage is applied to the anode and a positive voltage to the cathode, the SCR is in reverse blocking mode, making J1 and J3 reverse biased and J2 forward biased.
The device behaves as two reverse-biased diodes connected in series. A small leakage current flows. This is the reverse blocking mode.

What is unijunction transistor (UJT)?

A unijunction transistor (UJT) is a three-lead electronic semiconductor device with only one junction that acts exclusively as an electrically controlled switch. The UJT is not used as a linear amplifier.

What is power diode?

It has two terminals anode and cathode same as that of a ordinary diode. In fact, a power diode is nothing but a signal diode with a extra layer.


Top 10 PLC MCQ questions asked in previous year paper

Programmable Logic controller Multiple Choice Question

Top 10 PLC Programmable logic controller questions asked in various competitive exam. Please give this exam. This is free mock test and check your score.

First give this exam. If your answer is wrong then check below video for detail description of question

[ays_quiz id=”7″]

Series#1 ( Top 10 Questions )

Question 1 The acronym PLC stands for:

  1. Pressure Load Control
  2. Programmable Logic Controller
  3. Pneumatic Logic Capstan
  4. PID Loop Controller
  5. Pressure Loss Chamber

Answer: Programmable Logic Controller

Question 2 Ladder logic programming consists primarily of:

  1. Virtual relay contacts and coils
  2. Logic gate symbols with connecting lines
  3. Function blocks with connecting lines
  4. Text-based code
  5. Hieroglyphics

Answer: Virtual relay contacts and coils

Question 3 In a PLC, the scan time refers to the amount of time in which …..

  1. The technician enters the program
  2. Timers and counters are indexed by
  3. One “rung” of ladder logic takes to complete
  4. The entire program takes to execute
  5. Transmitted data communications must finish

Answer: The entire program takes to execute

Question 4 Identify the problem in this motor control PLC program:

  1. Coil
  2. Start contact
  3. Seal-in contact
  4. Stop contact
  5. Power source

Answer: Seal-in contact

Question 5 The Boolean representation of this PLC program is:

  1. ABC + D
  2. C + (A + B)D
  3. C + D(A + B)
  4. ABC + BD
  5. C(AB + D)

Answer: C(AB + D)

Question 6 The difference between online and offline PLC programming is . . .

  1. Whether the PLC is running or stopped
  2. Whether the programming PC has internet connectivity
  3. The type of programming cable used
  4. Where the edited program resides
  5. The type of programmer used

Answer: Where the edited program resides

Question 7 In PLC programming, a retentive function is one that:

  1. Defaults to the “on” state
  2. Comes last in the program
  3. Defaults to the “off” state
  4. Cannot be edited or deleted
  5. Is not reset after a power cycle

Answer: Is not reset after a power cycle

Question 8 Normally open contacts are open when:

  1. When Input is not energized
  2. When the input is energized
  3. When input is higher than 20 volts
  4. None of these

Answer: When Input is not energized

Question 9 An OR function implemented in ladder logic uses:

  1. Normally-closed contacts in series
  2. Normally-open contacts in series
  3. A single normally-closed contact
  4. Normally-open contacts in parallel
  5. Normally-closed contacts in parallel

Answer: Normally-open contacts in parallel

Question 10 A good application for a timed interrupt in a PLC program would be:

  1. A communications function block
  2. A PID function block
  3. A math function block
  4. A motor start/stop rung
  5. A “watchdog” timer

Answer: A PID function block

For more videos, Please check out my YouTube channel

https://www.youtube.com/channel/UC1QpfjrgQr0tPsaHGYd7PmA


FAQ’s

1. What is PLC ?

PLC stand for “Programmable Logic Controller”. It is a general purpose computer modified specifically to perform control task . It is a hardware device having microprocessor based control system. It is used in industrial automation.

2. What do you mean by PLC scan time?

PLC Scan Time is the time taken by the PLC to read the inputs, solve the Logic, and update the output is called a PLC Scan Time. This time is measured in millisecond .

3. Which is the most popular language in plc programming ?

The most popular language in plc programming is Ladder Logic Diagram.

4. What are the applications of PLC ?

PLC is used in industrial automation. These controllers can automate a specific process, machine function, or even an entire production line.

5. What are components of PLC system ?

There are major 6 components of PLC:
•Processor (CPU)
•Rack/Mounting
•Input Module
•Output Module
•Power Supply
•Programming Device/Unit

6. What is ladder diagram ?

Ladder diagram is the most popular programming language used in Plc programming. Ladder diagrams expresses a program as a series of “coils” and “contacts”, simulating the operation of electromechanical relays.
The advantage of ladder diagram is the familiarity many electricians have with the simple operation of relays.


Topics